
Extruded Aluminum Conveyor, Horizontal to Decline Series is a profile used for finished part applications where cleanliness and appearance are important. This conveyor is ideally suited for bedside the press applications to remove parts from under the machine or transition from another conveyor and lower down to another piece of equipment or discharge for inspection or assembly. The angle of decline is adjustable up to 60 degrees for elevation changes. The series' superior construction produces a solid square frame for industrial use.
Exclusive Series Features:
- Frame:
- Extruded aluminum frame, 6061 aluminum with T5 temper, clear anodized
- Cross Members:
- Steel cross members for exceptional torsional rigidity
- Casting:
- Supports bearings and pulleys featuring a Unique take-up design tracking adjustments at the four corners
- Side Rail Overlap:
- Recessed belt edges .75" per side up to 18" widths or less and 1.75" per side 24" and 30" wide"
- Cleated Belt:
- Standard polyurethane belts with either 20, 30, 40, 60 mm tall cleats on 15" centers
- Pulleys:
- Feature a machine trapezoidal crown on head and tail, which provides increase tracking signal
- Bearing Assembly:
- Set in castings with covers, no exposed rotating parts
- Belt Edge
Wear Strips: - Wear Strips on top and return sides, less belt damage on convey and belt return side
- Warranty:
- Five year limited

Technical Specifications:
- Frame: height, 13 gauge welded C channel steel frame fabricated with welded steel tubular cross members, optional steel slider bed for support. Incline frame section is adjustable up to 60 degrees
- Side Rails: 5″ extruded aluminum side rails without top return, overlap is .625″ per side, or 1.625″ per side on 24″ and 30″ wide models. Belt widths greater 18″ have a R16, 3.5″ tall stainless steel rail as a standard
- Belt: 2 ply white FDA Approved P.U. cover, Anti-Static with ¾″ cleats welded on 15″ centers, splice is endless bias angle skive type
- Belt Widths: 6″, 12″, 18″, 24″, 30″, 36″ (standard)
- Length:Combined Lengths to a max. of 15′ (2′ min on drive) and (2.5′ min. on take-up end), manufactured in 1′ increments (standard)
- End Drive: Located at in-feed end, M1, M2, are standard M9, M10, M11, M12 are available at no charge. Side drive positions M5, M6 are available. Positions M3, M4, M13, M14, M7, M8 are available if applicable (please consult factory) Standard drives are 120VAC/1/60 HZ motors
- Speeds: 22 FPM (standard), 45, 67, 133 FPM - available at a nominal charge
- Pulley: 3″ Drive & tail pulleys are both machined with trapezoidal crowns, shafts are 5/8″ diameter and bearings are sealed self-aligning type, no lubrication required. Drive pulley is fully lagged
- Take-up Assembly: Allows for 2.5 inches of take-up of belt adjustment
- Electrical Control: NEMA 1 enclosure with push button manual motor starter with thermal overload protection and 12′ of SJ 16/3 cord with plug for 120VAC input power as standard
- Supports: Steel telescoping type supports, LS2 series included with CA3 (4″ diameter swivel toe locking casters) Elevation is 11.9″-16.9″ top of belt to floor with cleats up to 30 mm tall
- Paint: Powder coated industrial finish (other colors available as options)
Common Options:
Drive Motor Location: Motor locations for special elevation requirements or functions
Variable speed drives: AC and DC type variable speed drive packages for different input voltages
Belts: Wide selection of various belt materials, cleat heights, spacing, and V-guides
Reversing Packages: Automatic processing reversing control packages
Indexing Packages: Automatic belt indexing packages
Side rails: Alternative side rail height and materials
Covers for Top of Conveyors: Polycarbonate & stainless steel covers
Covers for Bottom of Conveyors: Bottom covers- painted steel and stainless steel
Conditioning Units: Ambient air blowers and chilled water fed cooling blowers


Contact our Customer Service Team at 800-435-6979
or
This email address is being protected from spambots. You need JavaScript enabled to view it.